GMC

/GMC

We Service and Repair Most GMC Cars and Trucks

2010 GMC Yukon XL

2021-10-07T22:03:14+00:00

GMC Yukon XL

Mileage
140,154
Service Date
10/6/2021
Services Performed
  • Performed scan test & electrical diagnosis – Found: B0081 U0198 B0423 B2555 C0900 U0073 B1850 B1325 B2555 U0073 Most codes were lost communication codes – Checked all body, engine, & frame grounds. Found a frame ground that the connector was corroded. Replaced connector – Cleared codes & test drove over 200 miles. No codes returned and no issues were present.
  • Rotated Tires.
  • Oil Change Service
  • Waste Oil Removal
  • 20 Point Inspection
 
Luke H. gave our service a 5 star review on 10/6/2021
2010 GMC Yukon XL 2021-10-07T22:03:14+00:00

2004 GMC Sierra

2021-09-14T22:00:36+00:00

GMC Sierra

Mileage
168,265
Service Date
9/9/2021
Services Performed
  • The noise is due to lifters either failing or needing cleaned. Performed and oil change and added an additive to try and clean the lifters if sticky. Need to drive vehicle and see if ticking goes away. If noise doesn't go away engine will need lifters replaced. The oil pressure is due to the oil pump is getting weak and will need replaced.
  • Oil Change Service
  • Waste Oil Removal
  • 20 Point Inspection
  • Found front brakes are good but the rears are down to almost 20%. Replaced rear pads and rotors.
  • Replace rear brake pads. Replace rear brake rotors. Clean and lubricate brake calipers and slide mechanisms. Check and fill brake fluid. Bleed air from system. Road test vehicle.
 
Devin M. gave our service a 5 star review on 9/13/2021
2004 GMC Sierra 2021-09-14T22:00:36+00:00

2005 GMC Envoy

2021-06-16T22:03:02+00:00

GMC Envoy

Mileage
181,089
Service Date
6/15/2021
Services Performed
  • Found there was actually 2 codes in the system. P0014B referring to the exhaust camshaft position system performance and P2119C referring to the throttle closed performance. The variable valve timing solenoid is failing internally causing the P0014 code. This part is part of the timing system and will affect the way the vehicle performs. The other code is for the throttle body. The throttle body is failing internally. The throttle portion which is controlled by the pcm isn't opening and closing when commanded. Replaced both components and cleared the codes. Vehicle is operating as designed.
  • Missouri Vehicle Inspection
  • THROTTLE BODY ASSEMBLY – Remove & Replace – In-Line6
  • VARIABLE VALVE TIMING SOLENOID – Remove & Replace – In-Line6 – [NOTE: Labor estimates listed are for R&R only and DOES NOT include diagnosis time.]
 
Tricia W. gave our service a 5 star review on 6/15/2021
2005 GMC Envoy 2021-06-16T22:03:02+00:00

2007 GMC Yukon

2021-06-04T22:04:58+00:00

GMC Yukon

Mileage
139,415
Service Date
6/3/2021
Services Performed
  • Performed test drive & visual inspection – Found front & rear brake rotors are warped.
  • Replace rear brake linings. Inspect condition and thickness of rear brake disc rotors. Machine both rear brake rotors. Retract rear brake caliper actuators. Clean and lubricate rear brake caliper slide mechanism. Adjust parking brake. Road test vehicle.
  • Replace front brake pads & machine front brake rotors.
  • Oil Change Service
  • Waste Oil Removal
 
Pam W. gave our service a 5 star review on 6/3/2021
2007 GMC Yukon 2021-06-04T22:04:58+00:00

2012 GMC Terrain

2021-05-21T22:03:03+00:00

GMC Terrain

Mileage
155,062
Service Date
5/20/2021
Services Performed
  • 20 Point Inspection
  • Oil Change Service
  • Waste Oil Removal
 
Sheila G. gave our service a 5 star review on 5/20/2021
2012 GMC Terrain 2021-05-21T22:03:03+00:00

2006 GMC Yukon XL

2021-03-19T22:04:26+00:00

GMC Yukon XL

Mileage
159,336
Service Date
3/18/2021
Services Performed
  • Performed a visual under car inspection – Found source of oil leak is the oil pan gasket & rear main seal. Customer declined any further repairs at this time.
 
Derrick T. gave our service a 5 star review on 3/18/2021
2006 GMC Yukon XL 2021-03-19T22:04:26+00:00

2008 GMC Yukon

2021-03-06T23:01:34+00:00

GMC Yukon

Mileage
135,925
Service Date
3/3/2021
Services Performed
  • CAMSHAFT POSITION SENSOR – Remove & Replace – Denali
  • CANISTER VENT SOLENOID – Remove & Replace
  • EVAPORATIVE CANISTER PURGE SOLENOID – Remove & Replace
  • Performed a engine scan diagnosis – Found codes: P0340 – Camshaft position sensor circuit Performed flow chart tests – Confirmed the Camshaft sensor is bad – Recommend replacement. P0455 – Purge valve leak large leak detected Performed a flow chart test – Confirmed the Canister vent valve is bad – also the canister purge solenoid is stuck open (Bad).
 
James B. gave our service a 5 star review on 3/5/2021
2008 GMC Yukon 2021-03-06T23:01:34+00:00

2006 GMC Sierra

2021-02-19T23:02:52+00:00

GMC Sierra

Mileage
278,243
Service Date
2/18/2021
Services Performed
  • WATER PUMP – Remove & Replace – V8,Gas,5.3L Eng w/Air Cond
  • Water pump was leaking. Replaced the water pump and thermostat as an assembly.
 
Scott D. gave our service a 5 star review on 2/18/2021
2006 GMC Sierra 2021-02-19T23:02:52+00:00

2012 GMC Terrain

2020-10-06T22:01:49+00:00

GMC Terrain

Mileage
139,500
Service Date
10/5/2020
Services Performed
  • Brake pads: Front Rear Belts: Fluids:
  • Waste Oil Disposal Fee
 
Sheila G. gave our service a 5 star review on 10/5/2020
2012 GMC Terrain 2020-10-06T22:01:49+00:00

2005 GMC Envoy

2020-09-23T22:01:58+00:00

GMC Envoy

Mileage
190,008
Service Date
9/22/2020
Services Performed
  • found the LF wheel bearing excessive wear/play and cv boot shaft torn
  • replaced the left front cv half shaft/complete
  • replaced the LF wheel bearing
  • fuel
 
Ken W. L. gave our service a 5 star review on 9/22/2020
2005 GMC Envoy 2020-09-23T22:01:58+00:00